When your water heater isn’t working, it can be a major inconvenience. You may not have hot water for showers, dishes, or laundry. Not to worry! We’re here to help. In this article, we will discuss 10 possible reasons why your water heater is not working and what you can do about it. We’ll also give you some tips for maintaining your water heater so that you can avoid these problems in the future.
Diagnosing Issues With Your Water Heater – Before You Begin
Before we dive into the reasons why your water heater might not be working, it’s important to run through a quick diagnostic checklist. This will help you narrow down the potential causes of the problem and make troubleshooting easier.
Before you do anything, it’s important to take some safety precautions. Electric water heaters are high-voltage appliances and gas-powered appliances need to be inspected with care. First, shut off the power to your water heater. If you have an electric water heater, this means flipping the switch on your circuit breaker. If you have a gas water heater, this means turning off the gas at the valve. If it is necessary to handle any wiring, test wires with a voltage tester.
Once the power is off, open the cold water supply valve to release any pressure in the tank. Then, open the drain valve at the bottom of the tank and let some water drain out. This will help prevent any scalding if there is hot water in the tank. Now that you’ve taken these safety precautions, you can start troubleshooting your water heater.
Check Your Warranty
If you have a commercial or residential water heater and it is fairly new, yours may still be under warranty. Be sure to check the manufacturer’s website or your sales receipt to see if your water heater is still covered. Many warranties are only for a certain number of years and will not cover damage from normal wear and tear. If you need to call the manufacturer, find the rating plate on the water heater which holds important information such as model, serial number, manufacturing year, and more.
Recognize The Warnings Signs
Water heaters can give some warnings that they are on their last legs such as:
- Not enough or no hot water
- Varying temperatures
- Reduced water flow
- Smelly/discolored water
Don’t ignore these signs. Call a professional and get your water heater assessed before it goes out or causes damage to your home.
Additional Reading: 10 Noticeable Signs Your Water Heater is Going Bad
How to Diagnose the Problem with Your Hot Water Heater
If you think there might be a problem with your water heater, there are a few things you can do to try to diagnose the issue.
Check Your Power
One of the most common issues is that a hot water heater is not receiving power. First, check the circuit breaker or fuse box. If the breaker has been tripped or a fuse has blown, it will need to be reset or replaced before you can continue using your water heater.
Inspect Your Pilot Light
If your water heater uses gas, it will have a pilot light. This small flame ignites the burner whenever hot water is needed. If the pilot light has gone out, you’ll need to relight it. The process will depend on the model of your hot water heater.
You might find the instructions on how to relight your water heater’s pilot light glued to your water heater. If you don’t find them there you will need to determine if your water heater model needs to be manually or electronically ignited. You can find that information on the manufacturer’s website or in your hot water heater manual.
Test Your Water
Checking your hot water heater for both temperature and discoloration is essential. Cold water and brown muddy water indicate two very different issues. While cold water can be caused by the issues we have already covered, discolored water can come from a few different issues.
- Mineral and sediment buildup
Still No Hot Water? Here Are 10 More Possible Causes
If you have ruled out the issues we have already covered and you are still not getting any hot water, there are a few more potential causes to investigate.
1. Water Leaks
One of the most common reasons a water heater stops working is leaks. Check all around your water heater for any signs of water. If you see water, it could be coming from one of these three places:
- Drain valve
- Pressure relief valve
If your water heater is leaking, turn off the power to the unit and call a plumber or water heater repair person to come to take a look. Do not try to repair a leaking water heater yourself.
2. Gas Leaks & Faulty Gas Valves
If your water heater is powered by gas, a gas leak may be the reason why it’s not working. If you smell gas, turn off the power to the unit and call your gas company immediately. Another possibility is that the gas valve on the water heater is faulty and needs to be replaced. Do not try to repair a gas leak or faulty gas valve yourself. This is a job for a qualified technician.
3. Faulty Heating Element
If your water heater has an electric heating element, it could be the reason why your water heater isn’t working. If you have a digital multimeter you can test the water heater’s voltage and resistance based on the owner’s manual. If it doesn’t return a reading your heating element is faulty and the heating element needs to be replaced. If you aren’t comfortable testing your water heater’s heating element then call a qualified technician.
4. Faulty Temperature Pressure Valve
As water heats up in a water heater it expands. The temperature pressure valve releases water from the tank when the pressure gets too high. If this valve is not working properly and doesn’t turn off when the correct temperature is reached, it can cause the water heater to stop working. If you notice dampness under the discharge line, first turn down the temperature of your water heater. If the dampness is still there, call a qualified professional to fix the faulty temperature pressure valve.
5. Rust & Corrosion
Rust and corrosion can go unnoticed until you have a leak in your water heater. Discolored water is a key indicator that something is off with your water heater and should be investigated. If you think your water heater may be rusting or corroding on the inside, it’s best to call a professional for help.
6. Failing Anode Rod
The sacrificial anode rod is a part of the water heater that protects it from rust and corrosion. Over time, the anode rod will deteriorate and need to be replaced. If it is not replaced, the water heater may rust and eventually fail.
7. Thermostat Control Issues
The water heater thermostat plays an important role in keeping your water heater at the right temperature. If the water heater thermostat is not set to the correct temperature the water may be too hot or too cold. The thermostat is hardworking, constantly maintaining the temperature of your water even if the water heater isn’t in use so it is important to have it set correctly.
8. An Improperly Sized Water Heater
Sometimes a water heater isn’t sized properly for the household. As too many people try to access hot water simultaneously, the water heater can’t keep up. This usually results in lukewarm water or no hot water at all.
9. Damaged Burner Assembly or Gas Control
In a gas water heater instead of an element, you have a burner assembly. If there is no hot water or not enough hot water, the problem may be with the burner assembly or gas control valve. The gas burner is one part of the larger burner assembly. This includes the thermocouple, main orifice, main gas supply tube, pilot burner, pilot orifice, and pilot burner gas supply. If any of these elements are clogged or not functioning properly, then the entire system won’t work as intended. Over time, all these components can become damaged and will eventually need to be replaced.
Like anything, age can be a reason your water heater isn’t working. If your water heater is over 10 years old, it may need replacement. Over time, the elements in your water heater will break down and become less effective. The anode rod will also eventually stop working properly, leaving your water heater vulnerable to rust and corrosion.
Additional reading: How Much Does it Cost To Replace a Water Heater?
Avoid Future Issues with Regular Maintenance
Your water heater needs to be properly maintained in order to work properly. You should flush your water heater at least once a year to remove any sediment that has built up. You should also check the anode rod periodically and replace it if necessary. If you don’t maintain your water heater, it will be more likely to break down and stop working
Water Heater Inspection and Replacement Services in Portland
There are many factors that go into deciding when to replace your water heater and Jacobs Heating & Air Conditioning experts are here to guide you. We carry a variety of hot water heaters so that your home or business has the best and most efficient water heaters around.
Avoid extra costs and fewer repairs by scheduling a maintenance check for your existing water heating system before issues arise. No matter what you need, we’re always just a phone call away.
Whether you are in the market for a new water heater or simply have questions about your current one, Jacobs Heating & Air Conditioning is here to help. We’ve been servicing the Portland area for over 70 years and our experience shows in the quality of our work. Give us a call today!
If an electric water heater is not producing hot water, it could be a simple problem like a blown fuse or tripped circuit breaker. Additionally, some electric water heaters have a circuit-style safety switch located near or on the thermostat.Why is my hot water and heat not working? ›
Check Your Power. One of the most common issues is that a hot water heater is not receiving power. First, check the circuit breaker or fuse box. If the breaker has been tripped or a fuse has blown, it will need to be reset or replaced before you can continue using your water heater.What to check if water heater is not working? ›
- Check the thermostat.
- Check the pilot light. If your home has a gas water heater, check the pilot light. ...
- Restart your water heater. If your water heater is electric, try restarting it. ...
- Check your breaker box. If your water heater is electric, you can also check your home's circuit breaker box.
When your air conditioner “creates” cold air, it produces heat as a byproduct. All that heat goes to waste, so you're getting what you want (being cold air), but also wasting all that heat in the process. Even if you don't utilize that excess heat, your water heater and air conditioner can still impact one another.How do I know if my water heater fuse is blown? ›
A tripped breaker or blown fuse will result in total loss of hot water and is always the first thing to check. If, for any reason the tank gets too hot, the high temperature safety switch will shut off all power to the water heater. You must then firmly push the red button on the top thermostat to reset it.Why am I getting no hot water or heating? ›
A very common cause of no hot water in the hot tap is that the pilot light has gone out on your boiler. This is required to ignite the gas that heats the water inside the boiler. If your pilot light is out, you'll need to follow your model's instructions to ensure you're relighting the pilot light safely.What trips the reset button on a hot water heater? ›
When the water in your water heater gets too hot, it trips the emergency cut off, or ECO. In other words, water that is too hot will cause your water heater's reset button to trip. If your water heater is tripping the ECO repeatedly, there is likely a problem with the system that needs to be repaired immediately.Why do I have no heat or hot water? ›
This could be caused by a blockage in the system, or a faulty pump. Intermittent hot water and heat - These are typical signs of airlocks, low water levels, broken diaphragms, or faulty motorised valves. Tripped Circuit Breaker: The first thing to do when you have no hot water is to check the circuit breaker box.Why is my hot water not working but my cold water is? ›
If there is only cold water coming from the tap, it is likely your water heater, especially if the cold side is working fine. There are various reasons why water heaters do not heat properly. It may be due to a leak, a build-up of sediment or it could have become unplugged. Try to fix it by flushing the water heater.What kind of harm can air cause to a hot water heating system? ›
Air in Hot Water Line
There is some danger to your plumbing system if you have air in your water lines. Often times, the problem isn't severe. However, if left alone, air can cause corrosion and rust in your pipes.
Your air conditioning and plumbing system are linked together to keep moisture, humidity and water contained. Leaks, floods and moisture build-up can cause mold and mildew, especially in our humid climate. Extra moisture can cause a lot of damage.Does water run through HVAC? ›
Water is a natural part of your air conditioning system. As hot, humid air is cooled, it creates condensation on the evaporator coil. The condensation then drips down into the condensate pan, which is emptied outside through a drain line. Sometimes the drain line becomes clogged or damaged, which will cause HVAC leaks.